Home › Toilet cistern faults explained
Guide · Newborough plumbing

Toilet cistern faults explained

Most toilet problems start inside the cistern. Knowing what each part does makes it easier to work out what has gone wrong.

The parts inside a cistern

  • Inlet valve: lets water in after a flush and shuts off when the cistern is full.
  • Float: rises with the water and tells the inlet valve when to stop.
  • Outlet valve: at the bottom of the cistern, opens to flush and closes with a rubber seal.
  • Flush buttons: connected to the outlet valve by a linkage.
  • Overflow: a pipe that sends excess water into the bowl if the cistern overfills.

Fault: water keeps running into the bowl

Likely cause: the inlet valve is not shutting off and water is going down the overflow, or the outlet seal is leaking.

Check: take the lid off. If the water level is up at the top of the overflow pipe, the inlet valve is the problem. If the level is below the overflow but you can hear trickling, the outlet seal is leaking. The food colouring test helps here: add a few drops to the cistern and wait twenty minutes without flushing. Colour in the bowl means the outlet seal is leaking.

Fix: adjust or replace the inlet valve, or replace the outlet valve seal or the whole outlet valve.

Fault: the cistern fills slowly

Likely cause: a partly closed isolation tap, a blocked inlet valve filter or a faulty valve.

Fix: open the isolation tap fully, clean the filter or replace the inlet valve.

Fault: weak flush

Likely cause: water level set too low, worn outlet valve, a partial blockage in the pan or drain, or mineral build-up under the rim.

Fix: adjust the water level, replace the outlet valve, clear the blockage or descale the rim.

Fault: the button sticks or does nothing

Likely cause: a broken or misaligned button linkage.

Fix: realign or replace the button mechanism.

Fault: water on the floor

Likely cause: a leaking connection to the water supply, a failed seal between the cistern and pan, condensation on cold days, or a failed pan connector at the floor.

Fix: tighten or replace the connection, replace the seals or replace the pan connector. Condensation is not a leak, but it can be reduced with better bathroom ventilation.

Fault: the toilet rocks

Likely cause: loose floor fixings or a failed seal at the pan connector.

Fix: reseat the pan, replace the seal and secure it properly.

DIY or plumber?

Adjusting the float or water level is often simple. Replacing valves and seals needs the right parts for your brand and model. If you are not sure, or water is on the floor, ring 03 8658 7998. Most cistern repairs are finished in one visit because we carry common parts for the main brands.

Handy guides

More guides

Burst pipe: what to do in the first ten minutesA step-by-step guide for Newborough households when a pipe bursts: shutting off water, protecting the house, what to tell your plumber and insurer.Finding your water meter, stopcock and isolation valvesWhere to find the water meter, main stopcock and isolation valves in a typical Newborough home, how to turn them off and what to do if they are stuck.Frozen pipes in a Latrobe Valley winterHow to protect pipes, taps and hot water relief lines from frost in Newborough and the Latrobe Valley, and what to do if a pipe freezes or splits.Heat pump or electric hot water in the Latrobe Valley?Comparing heat pump, electric storage and solar hot water for Newborough and Latrobe Valley homes: running costs, cold winters, space, noise and rebates.Hot water temperature rules in Victoria, explainedA plain-English guide to hot water temperature rules in Victoria: the 60 degree storage rule, the 50 degree bathroom limit, tempering valves and scald safety.Leaking tap: fix it yourself or call a plumber?How to tell what kind of tap you have, which leaks you can safely fix yourself, and when to call a Newborough plumber instead.No hot water? A quick checklist before you callSimple checks for Newborough households with no hot water: switchboard breakers, off-peak timers, relief valves, tank leaks and when to call a plumber.Plumbing in Newborough's post-war homesWhat to expect from the plumbing in Newborough's original post-war houses: clay sewers, galvanised pipe, old hot water units and what to check when buying or renovating.Stormwater after a storm: what to checkWhat to check around your Newborough home after heavy rain: gutters, downpipes, pits, pooling water and signs your stormwater system is failing.Tree roots in old clay sewersWhy tree roots get into Newborough's old clay sewer pipes, the warning signs, how roots are cleared and the options for a permanent fix.
Book a plumber

Send us the job details

Send the details and a licensed plumber from Newborough will call you back. Water flooding or a sewer overflowing? Do not wait for a reply, ring 03 8658 7998 now.

03 8658 7998

Every job is quoted on what we actually find. That is why you will not see a price list on this site.







    Plumbing problem in Newborough?

    Ring a local licensed plumber. You hear the price before any work starts.